Aiuto configurazione cisco 877
Inviato: gio 03 apr , 2014 10:03 pm
Ciao ragazzi a differenza del 837 sul 877 non trovo l'interfaccia eth0 e
ho visto che qualcuno nel forum configura la VLAN 1 come fosse la eth0
è sbagliato farlo?
comunque questa config non mi va su internet ma molto lenta rispetto al router di telecom
potete darmi una mano od eventuali consigli?
forse aggiornando all'ultimo ios e fw adsl si risolve un po' con la velocità?
Grazie in anticipo
Building configuration...
Current configuration : 1512 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$2N.X$MN8dJ2o7PoE3lfNX1neJa.
!
no aaa new-model
!
!
dot11 syslog
ip cef
!
!
!
!
ip name-server 212.216.112.112
ip name-server 8.8.4.4
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
multilink bundle-name authenticated
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
pppoe-client dial-pool-number 1
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer0
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname aliceadsl
ppp chap password 7 060703284F4B081D161B
ppp pap sent-username aliceadsl password 7 14161E020F012B2F3724
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
!
!
!
control-plane
!
!
line con 0
password 7 04530A141B2456
login
no modem enable
line aux 0
line vty 0 3
password 7 030C0F19125C3B
login
line vty 4
login
!
scheduler max-task-time 5000
end
######################################################################
Stato modem
sh dsl interface ATM 0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'BDCM'
Chip Vendor Specific: 0x0000 0xA1F2
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' 'BDCM'
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0xB5
Serial Number Near: FHK101921X0
Serial Number Far:
Modem VerChip ID: C196 (0) capability-enabled
DFE BOM: DFE2.6 Annex A (0)
Capacity Used: 99% 100%
Noise Margin: 12.0 dB 12.0 dB
Output Power: 17.5 dBm 12.0 dBm
Attenuation: 8.0 dB 4.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x68
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8091 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-2.6.004.bin
Operation FW: AMR-2.6.004.bin
FW Source: external
FW Version: 2.6.4
DS Channel1 DS Channel0 US Channel1 US0
Speed (kbps): 0 15346 0 6
Cells: 0 49 0 1
Reed-Solomon EC: 0 134 0 0
CRC Errors: 0 139 0 0
Header Errors: 0 130 0 0
Total BER: 0E-0 1307E-8
Leakage Average BER: 0E-0 1307E-8
Interleave Delay: 0 0 0 5
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled
ho visto che qualcuno nel forum configura la VLAN 1 come fosse la eth0
è sbagliato farlo?
comunque questa config non mi va su internet ma molto lenta rispetto al router di telecom
potete darmi una mano od eventuali consigli?
forse aggiornando all'ultimo ios e fw adsl si risolve un po' con la velocità?
Grazie in anticipo
Building configuration...
Current configuration : 1512 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$2N.X$MN8dJ2o7PoE3lfNX1neJa.
!
no aaa new-model
!
!
dot11 syslog
ip cef
!
!
!
!
ip name-server 212.216.112.112
ip name-server 8.8.4.4
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
multilink bundle-name authenticated
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
pppoe-client dial-pool-number 1
!
dsl operating-mode auto
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Dialer0
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname aliceadsl
ppp chap password 7 060703284F4B081D161B
ppp pap sent-username aliceadsl password 7 14161E020F012B2F3724
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
!
!
!
control-plane
!
!
line con 0
password 7 04530A141B2456
login
no modem enable
line aux 0
line vty 0 3
password 7 030C0F19125C3B
login
line vty 4
login
!
scheduler max-task-time 5000
end
######################################################################
Stato modem
sh dsl interface ATM 0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'BDCM'
Chip Vendor Specific: 0x0000 0xA1F2
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' 'BDCM'
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0xB5
Serial Number Near: FHK101921X0
Serial Number Far:
Modem VerChip ID: C196 (0) capability-enabled
DFE BOM: DFE2.6 Annex A (0)
Capacity Used: 99% 100%
Noise Margin: 12.0 dB 12.0 dB
Output Power: 17.5 dBm 12.0 dBm
Attenuation: 8.0 dB 4.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x68
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8091 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-2.6.004.bin
Operation FW: AMR-2.6.004.bin
FW Source: external
FW Version: 2.6.4
DS Channel1 DS Channel0 US Channel1 US0
Speed (kbps): 0 15346 0 6
Cells: 0 49 0 1
Reed-Solomon EC: 0 134 0 0
CRC Errors: 0 139 0 0
Header Errors: 0 130 0 0
Total BER: 0E-0 1307E-8
Leakage Average BER: 0E-0 1307E-8
Interleave Delay: 0 0 0 5
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled