Ciao a tutti, è un po' che smanetto con VoIP e spero di aver trovato il posto giusto per imparare qualcosa.
questo è il mio 827:
Cisco IOS Software, C820 Software (C820-K9OSV6Y6-M), Version 12.4(1a), RELEASE SOFTWARE (fc2)
Cisco C827-4V (MPC855T) processor (revision 0xD01) with 48128K/1024K bytes of memory.
Processor board ID JAD06390G6O (1030454732), with hardware revision 0000
CPU rev number 5
4 POTS Ports
1 Ethernet interface
1 ATM interface
128K bytes of NVRAM.
12288K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)
ho felicemente appreso che si può sfruttare con protocollo SIP, quindi non vedo l'ora di farlo..
sono registrato a messagenet, ricevo tranquillamente chiamate con Xlite installato su un Thin Client HP!! vorrei fare la stessa cosa con un telefono tradizionale collegato ad una delle POTS.
qualcuno potrebbe postarmi una configurazione collaudata?
io intanto ho impostato così:
voice-port 1
timeouts interdigit 5
!
voice-port 2
timeouts interdigit 5
!
voice-port 3
timeouts interdigit 5
!
voice-port 4
timeouts interdigit 5
!
dial-peer voice 2 pots
destination-pattern 102
port 1
!
dial-peer voice 3 pots
destination-pattern 103
port 3
!
dial-peer voice 4 pots
answer-address 100
destination-pattern 100
port 4
!
dial-peer voice 1 voip
destination-pattern .T
session protocol sipv2
session target sip-server
session transport udp
dtmf-relay sip-notify
!
gateway
timer receive-rtp 1200
!
sip-ua
authentication username xxxxx password yyyyyyy
calling-info pstn-to-sip from name set Attila
retry invite 4
retry response 3
retry bye 2
retry cancel 2
registrar dns:sip.messagenet.it:5061 expires 3600
sip-server dns:sip.messagenet.it:5061
grazie in anticipo!
presentazioni e aiutino su 827-4v e messagenet
Moderatore: Federico.Lagni
-
- n00b
- Messaggi: 24
- Iscritto il: mar 02 ago , 2005 12:27 pm
provo a chiamare il mio numero geografico che con Xlite funziona ma ora è occupato:
un po' di debug:
bowtie#sh sip statu
SIP User Agent Status
SIP User Agent for UDP : ENABLED
SIP User Agent for TCP : ENABLED
SIP User Agent bind status(signaling): DISABLED
SIP User Agent bind status(media): DISABLED
SIP early-media for 180 responses with SDP: ENABLED
SIP max-forwards : 70
SIP DNS SRV version: 2 (rfc 2782)
NAT Settings for the SIP-UA
Role in SDP: NONE
Check media source packets: DISABLED
Maximum duration for a telephone-event in NOTIFYs: 2000 ms
SIP support for ISDN SUSPEND/RESUME: ENABLED
Redirection (3xx) message handling: ENABLED
Reason Header will override Response/Request Codes: DISABLED
SDP application configuration:
Version line (v=) required
Owner line (o=) required
Timespec line (t=) required
Media supported: audio image
Network types supported: IN
Address types supported: IP4
Transport types supported: RTP/AVP udptl
bowtie#sh sip connections udp brief
Total active connections : 0
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
bowtie#sh sip connections tcp brief
Total active connections : 0
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
Max. tcp send msg queue size of 0, recorded for 0.0.0.0:0
bowtie#sh sip register stat
Line peer expires(sec) registered
============ ============= ============ ===========
100 4 43 no
102 2 0 no
103 3 7 no
ho messo il server con ipv4 anzichè dns.
ora
bowtie#sh sip conn udp bri
Total active connections : 1
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
ma continua a dare occupato quando chiamo il numero geografico.
un po' di debug:
bowtie#sh sip statu
SIP User Agent Status
SIP User Agent for UDP : ENABLED
SIP User Agent for TCP : ENABLED
SIP User Agent bind status(signaling): DISABLED
SIP User Agent bind status(media): DISABLED
SIP early-media for 180 responses with SDP: ENABLED
SIP max-forwards : 70
SIP DNS SRV version: 2 (rfc 2782)
NAT Settings for the SIP-UA
Role in SDP: NONE
Check media source packets: DISABLED
Maximum duration for a telephone-event in NOTIFYs: 2000 ms
SIP support for ISDN SUSPEND/RESUME: ENABLED
Redirection (3xx) message handling: ENABLED
Reason Header will override Response/Request Codes: DISABLED
SDP application configuration:
Version line (v=) required
Owner line (o=) required
Timespec line (t=) required
Media supported: audio image
Network types supported: IN
Address types supported: IP4
Transport types supported: RTP/AVP udptl
bowtie#sh sip connections udp brief
Total active connections : 0
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
bowtie#sh sip connections tcp brief
Total active connections : 0
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
Max. tcp send msg queue size of 0, recorded for 0.0.0.0:0
bowtie#sh sip register stat
Line peer expires(sec) registered
============ ============= ============ ===========
100 4 43 no
102 2 0 no
103 3 7 no
ho messo il server con ipv4 anzichè dns.
ora
bowtie#sh sip conn udp bri
Total active connections : 1
No. of send failures : 0
No. of remote closures : 0
No. of conn. failures : 0
No. of inactive conn. ageouts : 0
ma continua a dare occupato quando chiamo il numero geografico.
- tonycimo
- Cisco pathologically enlightened user
- Messaggi: 185
- Iscritto il: mer 26 gen , 2005 9:26 am
- Località: Roma
Perchè hai messo quesi numeri 100 ai dial peer pots ?
li va il tuo interno messagenet
li va il tuo interno messagenet
*************************************
Non rendere mai difficile il facile per mezzo dell'inutile....
Non rendere mai difficile il facile per mezzo dell'inutile....
-
- n00b
- Messaggi: 24
- Iscritto il: mar 02 ago , 2005 12:27 pm
faceva parte della vecchia configurazione che utilizzavo per chiamare tra di loro gli interni.tonycimo ha scritto:Perchè hai messo quesi numeri 100 ai dial peer pots ?
li va il tuo interno messagenet
quindi prendo un interno e ci metto il mio numero messagenet?
altri errori visibili nella configurazione?
grazie mille!
- mgcomp
- Cisco fan
- Messaggi: 59
- Iscritto il: sab 13 ago , 2005 4:56 pm
- Località: Verona
- Contatta:
Prova come ho fatto io a togliere
A me funziona!!! Penso che sia il server SIP di MessageNet che non acetta il caller-id fornito in quel modo...
Ciao!!
Fammi sapere!!
Codice: Seleziona tutto
calling-info pstn-to-sip from name set Attila
Ciao!!
Fammi sapere!!
-
- n00b
- Messaggi: 6
- Iscritto il: gio 20 ott , 2005 4:12 pm
Mi sono reg. anche io e mi hanno regalato un 827-4v ok x sip, mi puoi postare una config funzionantr?attila ha scritto: grazie
ciao