Vdsl Intred pppoe bridge
Inviato: lun 29 mag , 2017 6:08 pm
Buonasera a tutti,
mi hanno attivato da qualche settimana una vdsl 100/20, l'operatore è intred un isp quì del Bresciano, ma credo che non differisca dalla configurazione di TIM,
il mio problema è che non riesco a far passare la chiamata ppp che parte dal firewall (in questo caso il cisco fa solo da modem), il modello è un 1941 con una EHWIC-VA-DSL-A MULTIMODE questa è la configurazione:
qualche anima pia riesce a capire dove sbaglio? e magari a metterci una pezza ,con un tplink in bridge tutto funziona normalmente.
Grazie a chiunque abbia una dritta
Andrea
mi hanno attivato da qualche settimana una vdsl 100/20, l'operatore è intred un isp quì del Bresciano, ma credo che non differisca dalla configurazione di TIM,
il mio problema è che non riesco a far passare la chiamata ppp che parte dal firewall (in questo caso il cisco fa solo da modem), il modello è un 1941 con una EHWIC-VA-DSL-A MULTIMODE questa è la configurazione:
Codice: Seleziona tutto
c1941#sh run
Building configuration...
Current configuration : 1778 bytes
!
! Last configuration change at 16:23:48 UTC Mon May 29 2017 by admin
!
version 15.6
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname c1941
!
boot-start-marker
boot-end-marker
!
!
enable password
!
aaa new-model
!
!
!
!
!
!
!
aaa session-id common
!
!
!
!
!
ip domain name c1941.local
ip cef
no ipv6 cef
multilink bundle-name authenticated
!
password encryption aes
!
!
!
!
username admin privilege 15 password
!
redundancy
!
!
controller VDSL 0/0/0
operating mode vdsl2
firmware filename flash:VA_A_38k1_B_38h_24g1.bin
!
bridge irb
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 192.168.0.13 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
no ip route-cache
duplex auto
speed auto
!
interface GigabitEthernet0/1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
!
interface ATM0/0/0
no ip address
no ip route-cache
shutdown
no atm ilmi-keepalive
!
interface Ethernet0/0/0
no ip address
!
interface Ethernet0/0/0.835
encapsulation dot1Q 835
bridge-group 1
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip ssh server algorithm encryption aes128-ctr aes192-ctr aes256-ctr
ip ssh client algorithm encryption aes128-ctr aes192-ctr aes256-ctr
!
!
!
!
!
!
control-plane
!
bridge 1 protocol ieee
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
transport input ssh
!
scheduler allocate 20000 1000
!
end
c1941#
Grazie a chiunque abbia una dritta
Andrea