Pagina 1 di 1
Cisco 1841 e onboard switch port
Inviato: dom 16 ago , 2015 6:47 pm
da ottobrerosso
Ciao a tutti,
sono ancora qui a chiedere consigli...
HO preso un modulo HWIC (HWIC-4ESW) con 4 porte fastEthernet.
La mia idea sarebbe quella di configuarle come se fossero uno switch vero e proprio collegato al router, ma mi sono accorto che non è proprio la stessa cosa... -.-''
Volevo chiedere come poter far si che queste porte possano "parlare" con il router?
Ho provato a collegare il pc ad una di esse e mi aspettavo che il pool DHCP che ho configurato facesse il suo e tutto finiva li, invece non è andata come mi aspettavo...
Cosa devo fare ?
Grazie a tutti!
Re: Cisco 1841 e onboard switch port
Inviato: dom 16 ago , 2015 8:17 pm
da paolomat75
Posta la configurazione.
Paolo
Re: Cisco 1841 e onboard switch port
Inviato: dom 16 ago , 2015 8:55 pm
da ottobrerosso
Ciao,
ecco qua,
ma non c'è nulla sulle porte... mi aspetto che se ci collego un cavo vada visto che sono integrate nel router... o no ?!?!
R1841#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.135.100.254 YES NVRAM up up
FastEthernet0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 unassigned YES unset up down
FastEthernet0/1/1 unassigned YES unset up down
FastEthernet0/1/2 unassigned YES unset up down
FastEthernet0/1/3 unassigned YES unset up down
ATM0/0/0 unassigned YES NVRAM initializing down
ATM0/0/0.1 unassigned YES unset initializing down
Vlan1 unassigned YES NVRAM up down
NVI0 unassigned NO unset up up
Dialer0 unassigned YES NVRAM up up
R1841#
R1841#sh running-config
Building configuration...
Current configuration : 1908 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1841
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 10.135.100.254
ip dhcp excluded-address 10.135.100.253
!
ip dhcp pool Campus
network 10.135.100.0 255.255.255.0
default-router 10.135.100.254
dns-server 8.8.8.8
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
vpdn enable
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 10.135.100.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1410
no ip mroute-cache
speed 100
full-duplex
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/1/0
duplex full
speed 100
!
interface FastEthernet0/1/1
!
interface FastEthernet0/1/2
!
interface FastEthernet0/1/3
!
interface ATM0/0/0
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
atm restart timer 300
no atm ilmi-keepalive
atm pppatm link reset
bundle-enable
dsl operating-mode auto
hold-queue 224 in
!
interface ATM0/0/0.1 point-to-point
no ip route-cache
pvc 8/35
pppoe-client dial-pool-number 1
!
!
interface Vlan1
no ip address
!
interface Dialer0
ip address negotiated
no ip proxy-arp
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username user password 0 pwd
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 10.0.0.0 0.255.255.255
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
scheduler allocate 20000 1000
end
R1841#
Grazie
Re: Cisco 1841 e onboard switch port
Inviato: dom 16 ago , 2015 9:42 pm
da carini
ottobrerosso ha scritto:Ciao,
ecco qua,
ma non c'è nulla sulle porte... mi aspetto che se ci collego un cavo vada
Non ho capito quello che intendi fare, ma da quello che intuisco ti serve configurare una vlan per ogni porta che vuoi utilizzare su una rete differente
Codice: Seleziona tutto
[...]
interface FastEthernet0
description Connected to wireless
duplex auto
speed auto
!
[...]
interface FastEthernet2
description Connected to server
switchport access vlan 20
[...]
Codice: Seleziona tutto
c1801#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa1, Fa3, Fa4, Fa5, Fa6, Fa7, Fa8
20 Servers active Fa2
Re: Cisco 1841 e onboard switch port
Inviato: lun 17 ago , 2015 6:54 am
da ottobrerosso
Ciao,
a me serve far funzionare le porte fastethernet che ho collegato al router.
Provo a fare un esempio per essere più preciso.
Io ho configurato un Pool DHCP sulla network 10.135.100.0 / 24 Vlan 1, quello che mi aspetto se collegassi uno switch al router è che gli host collegati alle porte sulla vlan1 ricevano un indirizzo IP 10.135.100.X.
Però questo non succede...
Come faccio a far si che se collego un dispositivo ad una delle 4 porte questo riceva un indirizzo ip e parli col router ?
Spero di essere stato più chiaro.
Grazie!
Re: Cisco 1841 e onboard switch port
Inviato: lun 17 ago , 2015 9:05 am
da carini
ottobrerosso ha scritto:Ciao,
Come faccio a far si che se collego un dispositivo ad una delle 4 porte questo riceva un indirizzo ip e parli col router ?
Spero di essere stato più chiaro.
Grazie!
Come prima cosa controlla che la porta venga vista come status = up
Codice: Seleziona tutto
show ip interface brief
Interface IP-Address OK? Method Status Protocol
FastEthernet2 unassigned YES unset up up
Infine controlli che nella sezione del DHCP venga distribuito l'indirizzo corretto, puoi usare la guida di tech republic
http://www.techrepublic.com/article/con ... or-switch/
o
http://www.ciscopress.com/articles/arti ... 1&seqNum=5
Re: Cisco 1841 e onboard switch port
Inviato: lun 17 ago , 2015 11:12 am
da lorbellu
Come faccio a far si che se collego un dispositivo ad una delle 4 porte questo riceva un indirizzo ip e parli col router ?
Se non ho capito male, vuoi utilizzare le 4 porte come quello che sono; un modulo switch, analogamente ad un router "casalingo".
La domanda a questo punto è : "Vuoi che le tue Fast0/0 e Fast0/1 facciano parte del gruppo?"
- Se la risposta è NO, devi sconfigurare la Fast0/0 e configurare la VLAN1 analogamente alla Fast0/0. Ovviamente a quel punto, ciò che è collegato alla fast0/0 deve essere spostato ad una delle 4 porte del modulo ESW
- Se la risposta é SI, devi sconfigurare la fast0/0, attivare la fast0/1 e mettere fast0/0, fast0/1 e vlan1 in bridge tra loro, configurando l'IP sulla risultante interfaccia BVI.
Saluti
Re: Cisco 1841 e onboard switch port
Inviato: lun 17 ago , 2015 11:40 am
da paolomat75
Sottoscrivo quello che ti hanno detto.
Paolo
Re: Cisco 1841 e onboard switch port
Inviato: mar 18 ago , 2015 9:05 am
da paolomat75
Hai risolto?
Paolo
Re: Cisco 1841 e onboard switch port
Inviato: mar 18 ago , 2015 6:44 pm
da ottobrerosso
Ciao,
no scusate mi sto perdendo...
Ho un modulo con 4 porte switch collegato al router.
Da profano mi aspetto che se configuro un pool dhcp sul router e collego un pc ad una delle 4 porte questo prenda un indirizzo ip. Ma a quanto ho capito così non è perché devo modificare la configurazione fare un bridge, giusto ?
Detto questo il mio presupposto che le 4 porte switch funzionino come se vi fosse uno switch in trunk collegato al router direi che è sbagliato, corretto?
Detto questo per far si che le 4 porte switch funzionino come se avessi collegato uno switch al router cosa devo fare? Un bridge? Se si avete qualche info o guida a cui possa rifarmi?
Grazie!
Re: Cisco 1841 e onboard switch port
Inviato: mar 18 ago , 2015 11:26 pm
da paolomat75
Come ti ha suggerito lorbellu, hai 2 possibilità, quella con il bridge se vuoi usare la f0/0, oppure non usare la f0/0 e mettere l'IP sulla VLAN 1 (cosa più semplice). Non ho guide sotto mano, ma la seconda opzione è molto semplice.
Paolo
Re: Cisco 1841 e onboard switch port
Inviato: gio 20 ago , 2015 6:39 pm
da ottobrerosso
Ciao,
mi sa che comunque ho sbagliato qualcosa...
Codice: Seleziona tutto
R1841#sh running-config
Building configuration...
Current configuration : 2001 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1841
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 10.135.100.254
ip dhcp excluded-address 10.135.100.253
!
ip dhcp pool Campus
network 10.135.100.0 255.255.255.0
default-router 10.135.100.254
dns-server 8.8.8.8 8.8.4.4
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
vpdn enable
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 10.135.100.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1410
no ip mroute-cache
speed 100
full-duplex
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/1/0
duplex full
speed 100
!
interface FastEthernet0/1/1
!
interface FastEthernet0/1/2
!
interface FastEthernet0/1/3
!
interface ATM0/0/0
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
atm restart timer 300
no atm ilmi-keepalive
atm pppatm link reset
bundle-enable
dsl operating-mode auto
hold-queue 224 in
!
interface ATM0/0/0.1 point-to-point
no ip route-cache
pvc 8/35
pppoe-client dial-pool-number 1
!
!
interface Vlan1
description Interface VLAN1
ip address 10.10.10.1 255.255.255.0
ip helper-address 10.135.100.254
!
interface Dialer0
ip address negotiated
no ip proxy-arp
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username User password 0 pwd
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 10.0.0.0 0.255.255.255
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
scheduler allocate 20000 1000
end
R1841#
Grazie come sempre!
Re: Cisco 1841 e onboard switch port
Inviato: ven 21 ago , 2015 10:58 am
da paolomat75
Non hai fatto nessuna delle 2 opzioni.
Leva l'IP dalla Fastethernet0/0, metti quel IP sulla VLAN 1.
Ciao
Re: Cisco 1841 e onboard switch port
Inviato: ven 21 ago , 2015 3:35 pm
da ottobrerosso
Ciao,
forse ce l'ho fatta, ecco qua la nuova configurazione:
Codice: Seleziona tutto
R1841#show running-config
Building configuration...
Current configuration : 2220 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1841
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 10.135.100.254
ip dhcp excluded-address 10.135.100.253
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool Campus
network 10.135.100.0 255.255.255.0
default-router 10.135.100.254
dns-server 8.8.8.8 8.8.4.4
!
ip dhcp pool VLAN1
network 10.10.10.0 255.255.255.0
default-router 10.135.100.254
dns-server 8.8.8.8 8.8.4.4
lease 0 6
!
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
vpdn enable
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
ip address 10.135.100.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1410
no ip mroute-cache
speed 100
full-duplex
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet0/1/0
duplex full
speed 100
!
interface FastEthernet0/1/1
!
interface FastEthernet0/1/2
!
interface FastEthernet0/1/3
!
interface ATM0/0/0
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
atm restart timer 300
no atm ilmi-keepalive
atm pppatm link reset
bundle-enable
dsl operating-mode auto
hold-queue 224 in
!
interface ATM0/0/0.1 point-to-point
no ip route-cache
pvc 8/35
pppoe-client dial-pool-number 1
!
!
interface Vlan1
description Interface VLAN1
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1410
no ip mroute-cache
!
interface Dialer0
ip address negotiated
no ip proxy-arp
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username User password 0 pwd
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 10.0.0.0 0.255.255.255
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
scheduler allocate 20000 1000
end
R1841#
R1841#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 10.135.100.254 YES NVRAM up up
FastEthernet0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 unassigned YES unset up up
FastEthernet0/1/1 unassigned YES unset up down
FastEthernet0/1/2 unassigned YES unset up down
FastEthernet0/1/3 unassigned YES unset up down
ATM0/0/0 unassigned YES NVRAM up up
ATM0/0/0.1 unassigned YES unset up up
Vlan1 10.10.10.1 YES NVRAM up up
NVI0 unassigned NO unset up up
Virtual-Access1 unassigned YES unset up up
Dialer0 87.5.140.141 YES IPCP up up
R1841#
R1841#sh ip dhcp binding
Bindings from all pools not associated with VRF:
IP address Client-ID/ Lease expiration Type
Hardware address/
User name
10.10.10.2 0178.24af.889c.a8 Jan 01 1970 06:18 AM Automatic
10.135.100.1 0178.24af.889c.a8 Jan 02 1970 12:11 AM Automatic
R1841#
Manca qualcosa secondo voi? Devo fare altro?
Grazie!