Salve a tutti, ho un problema sullo spanning tree tra un apparato CISCO 4507 e un 3Com 8800.
Il problema è che il CISCO è diventato root per una vlan e non riesco a togliergli il root.
Ho per prima cosa alzato la priorità con il comando:
spanning-tree vlan 30 priority 61440
con le altre vlan ha sempre funzionato la con questa vlan no e non so come mai.
Ho provato altresì ad alzare il pathcost delle porte fisiche dei port-channel,
ed a ad alzare il priority-cost sia del port-channel che della porta 1/18 dove è attaccato un server ma senza nessun risultato.
Il mio centro stella è formato da 2 3com 8800 uno fa da root primary e una da secondary
il CISCO è attaccato (con un portchannel per switch Po1 verso il root primary Po2 verso il secondary) al 3Com secondary
Questo i log:
sh spanning tree root
Vlan Root ID Cost Time Age Dly Root Port
---------------- -------------------- --------- ----- --- --- ------------
VLAN0001 0 aaaa.aaaa.aaaa 5003 2 20 15 Po2
VLAN0030 61470 aaaa.aaaa.aaaa 0 2 20 15
sh span vlan 30
VLAN0030
Spanning tree enabled protocol ieee
Root ID Priority 61470
Address aaaa.aaaa.aaaa
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 61470 (priority 61440 sys-id-ext 30)
Address aaaa.aaaa.aaaa
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Role Sts Cost Prio.Nbr Type
------------------- ---- --- --------- -------- --------------------------------
Gi1/18 Desg FWD 4 240.18 P2p
Po1 Desg FWD 4 128.641 P2p
Po2 Desg FWD 3 128.642 P2p
sh spanning-tree bridge priority sy
VLAN0001 32769 (32768,1)
VLAN0030 61470 (61440,30)
sh spanning-tree vlan 30 active detail
VLAN0030 is executing the ieee compatible Spanning Tree protocol
Bridge Identifier has priority 61440, sysid 30, address aaaa.aaaa.aaaa
Configured hello time 2, max age 20, forward delay 15
We are the root of the spanning tree
Topology change flag not set, detected flag not set
Number of topology changes 2 last change occurred 6w0d ago
from Port-channel1
Times: hold 1, topology change 35, notification 2
hello 2, max age 20, forward delay 15
Timers: hello 1, topology change 0, notification 0, aging 300
Port 18 (GigabitEthernet1/18) of VLAN0030 is designated forwarding
Port path cost 4, Port priority 240, Port Identifier 240.18.
Designated root has priority 61470, address aaaa.aaaa.aaaa
Designated bridge has priority 61470, address aaaa.aaaa.aaaa
Designated port id is 240.18, designated path cost 0
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
BPDU: sent 1822062, received 0
Port 641 (Port-channel1) of VLAN0030 is designated forwarding
Port path cost 4, Port priority 128, Port Identifier 128.641.
Designated root has priority 61470, address aaaa.aaaa.aaaa
Designated bridge has priority 61470, address aaaa.aaaa.aaaa
Designated port id is 128.641, designated path cost 0
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
BPDU: sent 1822026, received 0
Port 642 (Port-channel2) of VLAN0030 is designated forwarding
Port path cost 3, Port priority 128, Port Identifier 128.642.
Designated root has priority 61470, address aaaa.aaaa.aaaa
Designated bridge has priority 61470, address aaaa.aaaa.aaaa
Designated port id is 128.642, designated path cost 0
Timers: message age 0, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
BPDU: sent 1822026, received 0
Non so che altro fare e sinceramente ho perso il filo del discorso.
Grazie anticipatamente a chi mi saprà aiutare.
Problemi STP tra CISCO e 3Com
Moderatore: Federico.Lagni
-
- Messianic Network master
- Messaggi: 1159
- Iscritto il: dom 11 mar , 2007 2:23 pm
- Località: Termoli
provato ad abbassare ulteriormente il bid del 3com?
-
- n00b
- Messaggi: 2
- Iscritto il: ven 20 mag , 2011 2:20 pm
Credo che il protocollo che il 3com abbia sia mstp poiche l'unico parametro che mi permette di cambiare sia il diametro.
In questo caso dovrei aumentarlo giusto?
Il BID lo devo fare sulla porta? perche non ho la divisione per vlan come nel cisco.
Thanks
In questo caso dovrei aumentarlo giusto?
Il BID lo devo fare sulla porta? perche non ho la divisione per vlan come nel cisco.
Thanks
-
- Messianic Network master
- Messaggi: 1159
- Iscritto il: dom 11 mar , 2007 2:23 pm
- Località: Termoli
non conosco 3com, mi spiace. Prova....
ciao!
ciao!
-
- Messianic Network master
- Messaggi: 1159
- Iscritto il: dom 11 mar , 2007 2:23 pm
- Località: Termoli
in effetti... omg, non ci ho proprio fatto caso ._.